Forum Post: RE: HMP3.0 SU372 defect processing "record-route"
Thank you , we too faced same issue , and we could not transfer the outbound call and getting 403 forbidden error in REFER message. After installing SU375 the issue got fixed. Thanks for posting the...
View ArticleForum Post: No Modem Modulation
I'm bringing up some Diva UM PRI/T1-24 PCIe cards under RHEL 6.9, all drivers and software installed without errors or problems, web GUI shows everything is working fine. I'm trying to do simple tty...
View ArticleForum Post: RE: Diva 4BR-8 PCI v2 and Windows 2008 Server 32 Bit driver issue?
I have exactly the same problem!
View ArticleForum Post: RE: Multiple applications
Hi alaa, Have you achieved your objectives to run multiple applications above the same protocol stack? -Can you share here please.. Thanks
View ArticleForum Post: RE: No Modem Modulation
You would need to be calling to/from a modem application, either through the CAPI interface or via the TTYs using AT commands. There are samples available with the Diva SDK download. Your post didn't...
View ArticleForum Post: RE: Need to pass request from SCCP to Application over m3ua
Any Suggestions please
View ArticleForum Post: RE: HMP 367 + T.38 fax
Jeff, I have just checked T.38 on SU375, the T.38+IPv6 problem still persists Ravil
View ArticleForum Post: DMV1200 Detects 33 voice boards instead of 30 , what are extra...
I have a DMV1200 board, I get Voice Board counts with sr_getboardcnt("Voice", &BoardCount); It returns 33 voice boards , with total of 132 voice channels. as DMV1200 is 120 channel , I expect...
View ArticleForum Post: Can I Install DMV1200 and D4PCIUF on one computer ?
I have DMV1200 and one Dialogic D/4PCIUF . Can I install both on one server ? if not how can I have fax feature with DMV1200 ?
View ArticleForum Post: Problems creating DIVA drivers with kernel 3.16
Help! I have trouble with the installation of: Hilfe! Habe Ärger mit der Installation von: - driver: Diva4Linux_installer_9.6-117-162.bin - system: Debian 8 Jessie (Kernel 3.16.0-4-amd64) -...
View ArticleForum Post: RE: DMV1200 Detects 33 voice boards instead of 30 , what are...
Pending the mediaload you are using they are probably fax channels in this case. You can confirm by running devmapdump from DOS CMD prompt and you will see those devices have assigned fax addr. Jeff
View ArticleForum Post: RE: HMP 367 + T.38 fax
Yes, that would be correct, since IPV6 support has not been added as of yet for the release. Its still a work in progress, and thus needs to be disabled on the OS level still. Jeff
View ArticleForum Post: RE: DMV1200 Detects 33 voice boards instead of 30 , what are...
Thanks Jeff, Yes I saw in devmapdump and they are Fax Channels.
View ArticleForum Post: PowerMedia XMS Release 3.2 Service Update 4 (Build 17220) Now...
Download available at http://www.dialogic.com/en/products/downloads/xms/xms3.2_sla.aspx New Features Added Configurable Password Policy --- PowerMedia XMS Release 3.2 Service Update 4 provides the...
View ArticleForum Post: RE: decodeMsg error endless loop
Was still causing high CPU load... this finally fixed in SU375
View ArticleForum Post: dialing in does not answer
I have a D/4PCIUS media board that stops answering and not sure what the problem is. the only way to get it working again is to restart the server. the board is in a HP ML110 Gen9 windows server 2012...
View ArticleForum Post: Module MAP cannot handle long message (segmentation)
Hello! I'm developing an application working with the DSI stack's MAP module. I was faced with a problem, the MAP module does not process long message from the TCAP module. Stack DSI runs in trial...
View ArticleForum Post: Install and configure Dialogic Corp Springware D/41JCT-LS (rev 01)
I am trying to install and configure a Dialogic Corp Springware D/41JCT-LS (rev 01) in 32bit CentOS ver. 6.9 and I see the following when I run the lspci command: Unassigned class [ff00]: I am also...
View Article