Forum Post: Sending Insert Subscriber Data using a DSI utility like S7 Play...
QUESTION: Dialogic MAP Programmer's manual does Not contain any description of the parameter named "Subscriber Data". If I want to send a MAP Insert Subscriber Data request (in order to change a...
View ArticleForum Post: RE: HMP is not Re regestring after an hour
-- SIP/2.0 200 OK Via: SIP/2.0/UDP 192.168.0.120:5060;rport=5060;received=192.168.0.120;branch=z9hG4bK-503ff-13979dd7-77b1d749-d5b0568 Call-ID: d5f2df0-0-13c4-65014-503ff-745e277-503ff From:...
View ArticleForum Post: How to debug PCM log files of a FAX call sent/received by Diva...
HI, I have a fax call sent/received by Diva board. Diva--ATA--Sip--ATA--Diva. Here am capturing the PCM logs at ATA. I want to know how to debug the PCM logs file generated by Diva FAX Calls? Please...
View ArticleForum Post: RE: no voice heard over the line channel ch=ipmB1C1...
How are you opening the GC line device handle in this case? Are you creating a full duplex route between the GC and voice devices? Make sure you also have correct IP address selected in the CLI...
View ArticleForum Post: RE: Dialogic JCT Series Board Install Problems
You mentioned prior the boards are showing in windows device manager even as questions marked next to them as unknown devices? If that is the case, then maybe some type HW issue. What physical server...
View ArticleForum Post: RE: Dialogic JCT Series Board Install Problems
Hello, the boards have never shown under windows device manager, the server is HP Proliant ML350, Gen9, and seems to have the latest BIOS (p92, v2.30) thanks.
View ArticleForum Post: RE: Dialogic JCT Series Board Install Problems
What PCI-E X factor are the slots of which the boards are sitting in this case? Jeff
View ArticleForum Post: RE: Dialogic JCT Series Board Install Problems
x16, also tried the others with correct power settings - none worked. thanks.
View ArticleForum Post: Hylafx Setup to use Diva
By looking at the driver install I think It shoudl be creating /dev/ttyds0X - 24 The card is a 24 port PCI card. T1 interface. However after running config i get Check Diva configuration ......
View ArticleForum Post: RE: Dialogic JCT Series Board Install Problems
Ok, sounds like some type of HW inter-op issue in this case. It would not be the first time that HP has made changes to their BIOS that broke back compatibility with older PCI-e boards. This was last...
View ArticleForum Post: Dialogic HMP and Hyper-V
I am having issues getting the DM3 virtual board to be recognized on 2 different Hyper-V VM's that I am working on. The Hyper-V machines are off site so I am loading the software remotely. I have...
View ArticleForum Post: RE: Dialogic HMP and Hyper-V
It is my understanding that HMP on virtual machines - is only supported on VMware ESXi
View ArticleForum Post: RE: no voice heard over the line channel ch=ipmB1C1...
Hi Jeff, We are using the same program. Our old server installed InxHMP_4.1_161 and the voice works fine. Now we installed the latest version of InxHMP_4.1_213 and it failed to play the voice. Every...
View ArticleForum Post: RE: Hylafx Setup to use Diva
Did you actually start the driver (and therefore the board) with ./Start ? And make sure you have configured the board to use the TTY driver.
View ArticleForum Post: RE: no voice heard over the line channel ch=ipmB1C1...
Hi, Did you recompile the application on the new build? I know there were a lot of changes internal components and such and it always recommended to recompile with that big of a jump in builds. Jeff
View ArticleForum Post: MST_ASCFTR_BUFFER_OVERFLOW
Hi, Does anybody has experience with MST module error? I get many onMstManagementEventIndication - [00]SCTP_MON0 - mstManagementEvent: [0x01]MST_ASCFTR_BUFFER_OVERFLOW error in my application. I have...
View ArticleForum Post: RE: Dialogic HMP and Hyper-V
While the above statement about only supporting VMware is true, there must be some other difference here which is inducing the issue at the remote site. With respect to the issue, is the HMP and HPET...
View ArticleForum Post: RE: Dialogic HMP and Hyper-V
The HMP device states that it is working properly. The HPET driver states that it cannot find enough free resources that it can use (Code 12). I have tried both SU 367 and 372. The log shows:...
View ArticleForum Post: RE: Dialogic HMP and Hyper-V
Ok, maybe this: www.dialogic.com/.../pm_hmp_win Jeff
View ArticleForum Post: Number of Channels
Hello, I'm relatively new to the Dialogic cards and have few questions: 1. How do I find out the number of channels on a detected board ? iterate with dx_open ? 2. Can anyone recommend a good review...
View Article