after configuring the diva media board I got this Update CFGLib information ... succeeded Check Diva configuration ... succeeded, look for changes now Start Diva SIPcontrol ... FAILED Activate DSI SS7 for Diva ... OK Successfully updated configuration of Diva drivers Successfully updated configuration of Dialogic Diva Analog-4 PCIe v1 PORT: 0 SN:40095 Successfully updated configuration of Diva TTY driver Successfully updated configuration of Diva CAPI driver why DIVA SIPcontrol Failed? and for testing the card, I followed the instructions in the following link www.dialogic.com/.../Diva_M_LIN but I failed I got Enter destination address: +2012******** --Conn_Req(+201*********) [247]: Connect_Con-- [247]:Info__Ind-- Release --Info__Res [247]:Disc_Ind-- --Disc_Res ********** Call cleared *********** how can I test the card?
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
SIPcontrol can fail to start if another application is already using port 5060. To test the analog line you can use Line Test, but it looks like you should enter 00 instead of + at the start of the number.
↧
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
asterisk uses the same port 5060 will this affect the configuration? and how can I integrate Asterisk with the Card? is it through the capi.conf file?
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
about the line test how could I do this on Linux ?
↧
Forum Post: RE: HMP 367 + T.38 fax
From a quick look I see this line after fx_rcvfax called: 10/12/2016 02:51:08.237 6072 6828 dm3fax APPL libdm3fax dxxxB6C2 :::: fx_rcvfax(0x4) returns 0 .... 10/12/2016 02:51:08.334 6072 6696 dm3fax INFO Dm3Fax dxxxB6C2 ---- OnHangupStatusEvt [112] in state FaxAnswer 10/12/2016 02:51:08.334 6072 6696 dm3fax DEBG Dm3Fax dxxxB6C2 ----- *QFC3 IS DONE* (St=112,0) Basically firmware is complaining that something with RX rate is wrong as per internal define I have: #define QFC3_MsgHangupStatusEvt_Status_RXB_UNSPECIFIED 0x70 /* 112 */ I see before the call that one setparm fails here: 10/12/2016 02:51:08.235 6072 6828 spwrfax APPL r4 dxxxB6C2 :::: fx_setparm(4, FC_RXCODING (0x23000020), 0x936a314) 10/12/2016 02:51:08.235 6072 6828 dm3fax APPL libdm3fax dxxxB6C2 :::: fx_setparm(0x4,0x23000020,0x936a314) 10/12/2016 02:51:08.235 6072 6828 dm3fax DEBG FaxDevice dxxxB6C2 == == SetParameter (0x23000020,0x4) 10/12/2016 02:51:08.235 6072 6828 dm3fax ERR1 libdm3fax dxxxB6C2 :::: fx_setparm returns -1 This could be the reason for failure. Jeff
↧
↧
Forum Post: RE: HMP 367 + T.38 fax
Thanks for your answer. I helped me to correct the code, but looks like the sending fax error is not related to it. 1)As I earlier said the G.711 fax is sent and received properly with the same fax settings and the same file (rtflog.G711.zip is attached). However there was an ipmB1C1 error which I don't understand. 2)The RX_CODING setting error has gone - it appears to not accept DF_JPEG_COLOR value and this fact was mentioned in the doc. Then what value should I set if fx_rcvfax is supposed to receive a RAW JPEG file? The latest tests are made with b/w tiff files. 3)New rtflog.T38.zip is attached. I found there a "CheckTiffFileIntegrity" error and that is weird cause there is no such error in G.711 fax session (file was the same).
↧
Forum Post: RE: SCTP assocition is going down immediately - Reg
the problem disappeared after rebooting the Server.
↧
Forum Post: RE: Error Activating Dev License for HMP: LicenseMangerAPI: - LicenseManager: GetNewJob: Host-based system but license file is not Host-based: lock code=, bVerifyID=0
Dragging up an old thread I know, but I am having this exact same issue... "LicenseManager: GetNewJob: Host-based system but license file is not Host-based: lock code=" I am also in a virtualized environment, I would hope by now this issue is resolved. I am also using an 'OEM' license file, so perhaps I need to contact my OEM. Was just hoping to avoid that, as it's always a pain getting attention on tickets which relate to third party software. Thanks! Edit - I've also already read thru the troubleshooting licensing sections, and while I did learn a bit more about how the licensing works - I was not able to resolve the issue. http://www.dialogic.com/support/helpweb/helpweb.aspx/921/diagnosing_dialogic_hmp_licensing_failures/page.aspx?id=929 http://www.dialogic.com/support/helpweb/helpweb.aspx/921/diagnosing_dialogic_hmp_licensing_failures/PM_HMP_WIN Still getting the error about host-based system. What determines if the system is "Host-based" or not?
↧
Forum Post: Endpoint address in IPMEV_NOTIFY_ENDPOINTID events always has a zero value
I'm using HMP 3.0 SU367 and enable IPMEV_NOTIFY_ENDPOINTID events by using ipm_EnableEvents with the EVT_ENDPOINTID_NOTIFY bitmask. The IPM_ENDPOINTID_INFO data that comes with IPMEV_NOTIFY_ENDPOINTID events occur as expected (with the initial received RTP packet in a call and on SIP re-INVITE's) but the ucIPAddress[0] and unPortId values are always zero; however all the other values are verified as valid (SSRC, payload type, payload size, sequence number, timestamp) and correct. Is that expected, a bug or something I'm missing? Its also a little unclear from the documentation (ip_media_api_hmp_v16.pdf) how to interpret the ucIPAddress value (defined as unsigned char ucIPAddress[IP_ADDR_SIZE]). The example code in the documentation (p106) shows that the value is to be cast as an unsigned long, placed in a in_addr structure and converted to a string using inet_ntoa. Yet in other places in the IPM library the address is a cIPAddress[IP_ADDR_SIZE] and interpreted directly as a zero terminated string. Is the documentation correct?
↧
↧
Forum Post: Where can I download the protocol binaries like m2pa_nt.exe, mtp_nt.exe, map_nt.exe?
I want to follow this tutorial to simulate the exchange of SMS over a Sigtran link. There is a point/step in the tutorial: "Download all the requested protocol binaries (m2pa_nt.exe, mtp_nt.exe, sccp_nt.exe, tcp_nt.exe, map_nt.exe) from the Dialogic website" But I am unable to find any of those binaries on the Dialogic website. So what should I do? Where can I download the protocol binaries?
↧
Forum Post: RE: Where can I download the protocol binaries like m2pa_nt.exe, mtp_nt.exe, map_nt.exe?
you have to download the windows dpk package here www.dialogic.com/.../dpkwin.exe
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
You can reconfigure SIPcontrol to use another port if you need it, say 5070 for example. Refer to this page for the Asterisk/SIPcontrol configuration: www.dialogic.com/.../Diva_M_LIN You can run the Line Test tool from the web GUI, but you can also use the other utilities from the command line to make/receive calls.
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
Thank you so much If I want to use this card on windows, does it support Asteriskwin32 or not ? and what are other Asterisk alternatives this card can support on windows ?
↧
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
There is no official support for Asteriskwin32 that I know of. For alternatives, google offers software like 3CX or Freeswitch, but there is nothing in the Dialogic knowledgebase regarding configuration or interoperability with those.
↧
Forum Post: RE: Install Diva Media board on Linux: Build error
Thank you so much
↧
Forum Post: RE: Error Activating Dev License for HMP: LicenseMangerAPI: - LicenseManager: GetNewJob: Host-based system but license file is not Host-based: lock code=, bVerifyID=0
Hi, In this case host-based means he HMP license is tied to a MAC address (NIC) on the physical system. Alternative option is where the HMP license is tied to the Serial Number of the DNI board in place. Sometimes there could be a system level issue where the host or MAC is not accessible or is being blocked from the system and thus cannot be matched to that encrypted in the license so it fails with that error as well. Also seen where the system has more than 5 NICs, and Flex can only read the first 5 in the priority list, and issue occurs if HMP license is tied to a NIC at a lower priority level. Jeff
↧
Forum Post: RE: Error Activating Dev License for HMP: LicenseMangerAPI: - LicenseManager: GetNewJob: Host-based system but license file is not Host-based: lock code=, bVerifyID=0
Jeff, Thanks for the response - I am missing something here, I have an 'OEM' license which should not be tied to any MAC address. I will probably have to take it up with my OEM, but thanks for the suggestions. This server just has a single vNIC.
↧
↧
Forum Post: RE: Where can I download the protocol binaries like m2pa_nt.exe, mtp_nt.exe, map_nt.exe?
The following are two steps described in the .pdf tutorial from the post I linked in my question: - "Download and install the Dialogic SS7 Development Package in c:\Septel (you don’t need to select any options since you are not using any SS7 cards in this particular case) - Download all the requested protocol binaries (m2pa_nt.exe, mtp_nt.exe, sccp_nt.exe, tcp_nt.exe, map_nt.exe) from the Dialogic website and put them into the c:\Septel folder. " You are talking about the first step. I have done that and after installation of the ss7 development package, I have got a "DSI" folder in C drive in Windows. The question is about the next step. I can't find the protocol binaries like m2pa_nt.exe, mtp_nt.exe, sccp_nt.exe, tcp_nt.exe and map_nt.exe .
↧
Forum Post: RE: Error Activating Dev License for HMP: LicenseMangerAPI: - LicenseManager: GetNewJob: Host-based system but license file is not Host-based: lock code=, bVerifyID=0
Ok, if its OEM then you need to contact the vendor. If my memory serves, I think you need to have a special key tied to the license entered into the windows registry such that it can be activated on the system. Only the third party vendor has this information as the implementation is specific to them. I can't provide that since we didn't write it, and they did. Jeff
↧
Forum Post: RE: Endpoint address in IPMEV_NOTIFY_ENDPOINTID events always has a zero value
Is this the first time you are developing this specific feature? Or had it worked in the past on a prior build and just noticed this issue now? I ask because I know some changes took place in the middle libraries for IP Host and DM3 HRT (host run-time) components within HMP baseline when merge was done for Linux/Windows releases of the source code recently. After that point some issues seen with IPML APIs have since then been addressed in the HMP 3.0 baseline (specifically 367). So I wonder if something else still needs to be addressed. I had not seen this API / event used in quite sometime, so I can't answer to that data point just yet. In reference to your other question, don't confuse the two different defines for IP address, as they are two different structures one which uses our own define for IP address in IPM_PORT_INFO that being char string. The other uses that of how its passed at Microsoft data structure level (that being in_addr defined by them) and then is stored in our structure. Jeff
↧