Forum Post: RE: SIP Instant Messaging via Dialogic HMP
You're right, the error was because I wasn't targeting the board level device. Now I just need to get my request uri formatted properly. Thanks!
View ArticleForum Post: RE: Resource Failure from component request
Hi Gabor, It's easy to check in the txalarm. If TCAP is going into congestion, you'll get some clear messages saying that. Here's an example going from uncongested to Level 1 and then Level 2:...
View ArticleForum Post: something wrong with modify the RTP address
I test the call,when I find the RTP flow cannot receive,I find that it should modify the RTP address of HMP. the normal step is. 1.shutdown the ipmedia 2.modify the RTP address 3.start the ipmedia as...
View ArticleForum Post: RE: Resource Failure from component request
Hi Greg, thank you for your fast answers again. I understood, that hitting the MAX_TCAP_DIALOGS / MAX_TCAP_INVOKES limits by incoming TCAP traffic is a type of "TCAP transaction throttling" and not...
View ArticleForum Post: RE: G723.1, Invalid parameter when calling imp_StartMedia
This is not the right forum for this question. This forum is about Dialogic Media Gateways, DMG1000/2000, DMG4000. Please try there: www.dialogic.com/.../7.aspx
View ArticleForum Post: RE: something wrong with modify the RTP address
In most cases I would check the system to make sure firewall is not blocking those specific ports used for RTP streaming. That being 49152 counting up by number ports *2 in your HMP license (rtp &...
View ArticleForum Post: reducing data modem handshaking time
Hello all of members in this forum. I have an issue with handshaking time of Diva V-2PRI board. It's slower 10 seconds than I expected. So if possible would you please anybody help me? Is there any...
View ArticleForum Post: PowerMedia™ XMS – Release 3.0 SU2 (Build 12399) Now Generally...
PowerMedia™ XMS – Release 3.0 SU2 (Build 12399) Now Generally Available and can be downloaded from the link below: http://www.dialogic.com/en/products/downloads/xms/xms3.0_sla.aspx Note that a valid...
View ArticleForum Post: Does SWS support unicode SMS?
Hello, Does SWS support unicode single SMS and concatenated SMS? Thanks
View ArticleForum Post: cg6565e comile but not running ctainitialize
== Parsing '/etc/asterisk/nms.conf': == Found == chan_nms:1333 load_module: trunks = 4 == chan_nms:1334 load_module: total timeslots = 120 == chan_nms:1335 load_module: partner modes = NT NT TE TE...
View ArticleForum Post: RE: cg6565e comile but not running ctainitialize
can any one here who can help regarding this
View ArticleForum Post: RE: ./gctload: error while loading shared libraries: |...
Hi Afshin You need to install 32 bit binaries in 64 bit OS machine because dialogic software supports only 32 bit.
View ArticleForum Post: SCCP Calling Party Address in outgoing TCAP P-Abort
Hi, our Application receives TC-BEG with SCCP.CdPtyAddr.RoutingIndicator=Route_on_SSN . Due to customer requirements the outgoing TCAP responses shall be sent out with...
View ArticleForum Post: RE: something wrong with modify the RTP address
it casue by the ifcfg-ethX where service NetworkManager block the HMP detect the ethernet port ,stop the service and modify the NM_CONTROLLED=yes = NM_CONTROLLED=no
View ArticleForum Post: RE: ./gctload: error while loading shared libraries: |...
Dear olrao Thank you very much for replay, Could you please help me to resolve this problem ? ./txa: error while loading shared libraries: libcpi.so: wrong ELF class: ELFCLASS64 for running ./txa how...
View ArticleForum Post: RE: ./gctload: error while loading shared libraries: |...
You can find those rpms/packages in OS Repository using yum command etc.
View ArticleForum Post: RE: Max Digit Phone Number
There may be a possibility to use GC send overlay digits method, but that depends on board in use (ie Springware vs DM3) and / or HMP/DNI? What SR and board do you have in this case? Jeff
View ArticleForum Post: Configure HMP to save CDR information (Jitter, Delay and Packet...
Hi Is it posible to configure/write code to save all CDR information from all call to and from a HMP device? We use HMP software for IVR functionality and I need to save CDR (Call Detail Records)...
View ArticleForum Post: BICC make call fails
Hi, I use Host license bicc, m3ua. I make call almost successfull. But sometimes I face this error on all channels when make call out going GCEV_DISCONNECTED gc_ResultInfo() successfully called...
View ArticleForum Post: RE: Configure HMP to save CDR information (Jitter, Delay and...
Hi, Is this for Linux or Windows HMP baseline? As there is a little bit of difference in what can be done between the two. But have some capabilities on getting RTCP reports in this case. On windows...
View Article